About Cut Wire shots

Cut Wire Shots

Product description

  • Cut wire shot is produced by cutting wire into lengths equal to the wire diameter.
  • If required the particles are rounded to remove the sharp corners.
  • The sharp edges of the cut shot may also be useful, in case of additional cleaning requirement.

Advantages

  • Improved Consistency: Exhibits highest consistency in terms of shape and size
  • Highest Durability: Has a wrought internal structure with almost no cracks, porosity, etc.
  • Low Dust Generation: Our Cut wire shots exhibit the lowest dust generation rate
  • Improved Part Fatigue Resistance: Our peened parts and specimens exhibit higher average and consistent life as compared to those peened with equivalent cast steel shot
  • Lowest Surface Contamination: Unlike other media, our shots do not leave any residue or Iron Oxide coating over the particle surface
Technical specification
Material SIZES CUT WIRE SHOT VICKERS HARDNESS RANGE ROCKWELL HARDNESS RANGE
Steel 0.10 mm - 1.60 mm
(.0039 inch - .062 inch)
Low Carbon Cut wire
shot Grade I
High carbon Cut wire
shot Grade II & III
< 35 Rc
45 - 55 Rc
55 - 62 Rc
< 350 HV
446 - 595 HV
595 - 697 HV
Stainless Steel 0.45 mm - 1.60 mm
(.017 inch - .062 inch)
Grade 302/304 Cut Wire
shot
Special Sys Cut wire shot
Min. 45 Rc
Min. 35 Rc
Min. 446 HV
Min. 350 HV
Aluminum 0.50 mm - 2.00 mm
(.020 inch - .080 inch)
Grade 5053 Cut Wire
Shot - Full Hard
Grade 1100-1345 Cut
Wire Shot - Full Hard
SOFT N/A
Zinc 0.61 mm - 3.35 mm
(.024 inch - .1319 inch)
Commercial Quality Pure
Zinc Cut Wire shot
SOFT N/A

Standards

Our cut-wire shot is certifiable to the following specifications:

  • IS:5873 arrow AMS–2431/8
  • MIS–S–13165 arrow SAE J441
  • AMS–2431/3B arrow VDF 8001
  • As per customer's requirement
SIZE IN MM SIZE IN INCH. CUT WIRE DESGN CAST SHOT DESGN. GRITS DESGN. SHOT PEENING DESGN.
0.1 0.0039 CW-4 S-40 G-120 P-4
0.2 0.0079 CW-8 S-70 G-80 P-8
0.3 0.0118 CW-12 S-110 G-50 P-11
0.36 0.0142 CW-14 S-140 G-45 P-13
0.43 0.0169 CW-17 S-170 G-40 P-16
0.51 0.0201 CW-20 S-200 G-35  P-19
0.58 0.0228 CW-23 S-230 G-30 P-23
0.71 0.028 CW-28 S-280 G-25 P-28
0.81 0.0319 CW-32 S-330 G-20 P-33
0.89 0.035 CW-35 S-360 G-19 P-35
1.04 0.0409 CW-41 S-390 G-18 P-39
1.19 0.0469 CW-47 S-460 G-16 P-46
1.37 0.0539 CW-54 S-550 G14 P-55
1.59 0.0625 CW-62 S-660 G-13 P-62
1.8 0.0709 CW-71 S-710 G12 P-71
2 0.0787 CW-79 S-780 G-10 P-78
2.38 0.0937 CW-94 S-930 G-8 P-93
2.82 0.111 CW-111 S-1110 G-7 P-111
3.35 0.1319 CW-132 S-1320 G-6 P-132